|
It has adequate power for what I'm using it for (plywood, MDF and hardwoods) and is fine for a small hobbyist woodworking shop. I was looking for good table saw at a good price. The order process, shipping and delivery went without a hitch (I actually got it three days earlier than promised).Set up took a friend and me about 90 minutes, and alignment checks another hour. The second was a defective end cap on the front rip fence rail.The saw was properly aligned and I had to make only a minor adjustments to the miter gauge and rip fence.Overall the saw runs very smoothly and quietly. I'm not sure if its a function of no vibration to move the dust along the bottom toward the dust collection port, or using a standard insert as opposed to a zero clearance insert. The manual was clear and consise.
I'm using a Delta Dust Collection system rated at 650 CMF. Feature for feature the Jet ProShop 10" met most of my selection criteria. I've run into a minor issue with dust collection and dadoing operations. A couple of notes on the assembly; we found most of the bolt holes in the frame had over spray from the powder coating process and that resulted in having to drive each bolt in all the way to clean it out before attempting to mount anything.I have two quality complaints; a large chunk of paint came off the side of the saw fame. This looks to be due to poor or inadequate surface preparation over about 15 square inches. Dust seems to collect in the bottom of the saw when dadoing.
It's not critical as long as you remember to clean it out as part of your shop clean up routine.Regrets; yeah, I should have purchased the 50" model (and built a bigger garage.
I read the other reviews about not getting the saw that was described. I recieved my saw on Dec. I did alot of research on saws and decided this is the saw I wanted. I never did recieve a call. I am very happy with my purchase.I am giving the saw 4 stars because alot of the hole during assembly were poorly tapped and very hard to get the screws started and I have no metric taps.Since the review is about the saw and not anything else, I would like to add a 2 star review to Amazon for not following up with a call. I did call Amazon about it and they said I would get the right saw. 14, I am sure they were very busy.
Opened it up and it was the very same saw that was described. I came across this listing, which was a very low price for the saw. 23, 1 day earlier then it was scheduled to be delivered. They would call me in a couple of days to confirm. I must say in there defense that I ordered it on Dec. It is a great saw and top notch quality. Also I see Amazon must have caught the wrong listing because the price has jumped 228.00 over what I just paid.
Your choice, on the inside or underneath the box stops the leakage of saw dust all over the ground. All the research that I put into this saw was not a wasted effort. They sure are eye candy for the Man Cave type person. I do agree with one reviewer's comments about putting tape in the four corners of the saw box. While doing this I had a certain budget in mind. The base, legs, table top, and fence are heavy duty - nothing wimpy there. They all are reliable, powerful, easy to assemble, and easy to care for. There was no additional drilling, pounding, or cursing to put it together.
Everything was boxed and packaged very well. However, don't be fooled, I was not looking for a wimpy saw. This is a limited tolerance saw. I also have a bunch of Jet tools at home and each one was and continue to be a solid performer. But Jet should try and put together a better blade guard for those that do use them.
Jet must have made some type of adjustments to the 708118 base because it fit perfectly. I purchased the saw and brought it home. Something that will be reliable, tough, and powerful that would last a very long time was the primary target. I decided to take a chance on the Jet 708482 after watching the Jet's web page where you can watch the 708482 in action. I never did use blade guards with my old saws and I am not going to start now. But for me, the huge price tag of one of those saws was simply unreasonable.
The only disappointing aspect of this saw was the blade guard. I recently purchased this table saw, and believe me, I have no regrets. All the key qualities that I was looking for. Finally, I was able to buy this saw, a Jet DC-1100 dust collector, a Jet AFS-1000 air filter, and save about $800.00 versus buying just one Powermatic cabinet saw.
It is flimsy and does not seem to go on or remove very well with this saw. I found nothing flimsy about the saw parts themselves. I would say it is quiet because the internal mechanism and table top is solid cast iron, thus dampening vibration and noise. If you enjoy weightlifting, this table saw would provide a nice workout during assembly (it weighs a bit under 300 lbs).Everything went together smoothly. It took about two and a half hours to assemble. All of us have looked at the Powermatic table saws and drooled all over the place wanting one. You sure are going to love the arbor lock (I have a nice scar tissue on my hand for raking my hand over a blade while trying to wrestle a blade off my old saw).
I am not a professional carpenter / cabinet maker, but a humble woodworker who enjoys making stuff (mostly furniture) at home. It has plowed through through maple, oak, and Koa with ease.This saw is also amazingly quiet. Jet even provides wrenches and Allen head screw drivers for the various nuts and screws. The bottom line is that this saw is a solid perfomer. The other reviews bashing this saw and Amazon for incorrect ordering and stock numbers is unfair to the saw itself.
I am like a lot of you out there, I was looking for a solid table saw for a reasonable price. Also, one reviewer stated that the 708119 was the proper base for the saw. I don't disagree, however, the 708118 was offered at a local retailer at a huge discount and I simply could not pass it up, and if it was wrong, I could always return it. Buy this saw you won't regret it.Good luck. Once I fully assembled the saw, the table top was dead flat, the fence glided over the table top effortlessly with the one finger, and the fence was perfectly aligned with the saw blade.
It also has plenty of power. I did countless hours of looking at Powermatic, Delta, and Jet table saw reviews on all the woodworking magazines, Amazon internet reviews, and gone down to a Woodcraft store to talk to the sales personnel on the pro's and con's on each saw. This saw will get good usage in my shop. While I did the assembly myself, I suggest you find some help. Everything fit very snuggly together (a good thing).
Everything was well built, heavy duty, powerful, and at a very reasonable price. More toys for less money - does it get any better than that.
When I called Jet, they informed me that the model JWTS-10CW2 has been discontinued and been updated to the 708482k.that's why the listing is screwed up. A bit confusing. As of 5/14/08 this listing for the Jet proshop 708482k is still a strange amalgamation of 2 Jet saw listings.the new proshop model 708482k is followed by the description for a completely different saw. Anyway, after I made the calls I decided to chance it. However, I did successfully order and receive the proshop with cast iron wings this very week from this listing. I called Amazon and they advised me to call Jet. A new Jet proshop is now in my garage. Haven't had time to assemble yet but I will edit this review and add my thoughts after I do.
Besides, I figured the cabinet saws were for those who work on them all day. Beyond that, little or no adjustments were needed. Can't install a full-width dado blade set since the arbor isn't long enough. Vibration was more than I expected (although this is the first "real" saw I've ever used). Almost everything had been adjusted perfectly at the factory. Angle and height adjustment wheels turn as if they're not even connected6.
That took some time to get right. Easy blade removal and installation.CONS1. Anything that did need adjusting was simple to do.I've used this saw several times and have decided it's a huge improvement compared to the cheapie it replaced. Once the pallet arrived and I wrestled the boxes into my shop with a friend, I spent a few nights assembling it. No motor protruding out the back -- saves space.5.
Assembly was easy except for the iron wings. I decided against a cabinet saw since I don't have THAT much room or money. Duct tape easily and discreetly fixes this.3. I got into woodworking much more than I expected and decided it was time to graduate to a real saw.I decided to pass on a contractor's saw since I had a little more room in the shop and a little more money to spend. Easy throat plate removal and installation7. Not sure if it was the saw itself or my strive for perfection when aligning the wings with the table. (My cheapie could easly handle a full-width dado set).5. Large, solid tabletop2.
I purchased this saw to replace a cheapie starter saw that I purchased at a local home improvement warehouse. Blade guard not easy to install2. Corners at bottom of saw "box" have holes that allow dust to fall through to the floor, even with a dust collector. However, if you replace the factory belt with a link belt, the vibration disappears.4. Very solid feeling overall3. Would like a plug disconnect on the saw itself instead of going to the wall to unplug it. I don't.It took two months for my saw to arrive, but I had no problems with that since I needed the time to finish up some projects and sell the old saw to make room for the new one. (My cheapie had this as well).Despite the cons, this saw is a joy to use and I don't regret my purchase one bit.
Here's my take on it:PROS1. Great fence -- easy to move and adjust4. I'm still looking into this, however, to see if I'm missing something. I expect to keep and use this saw for the next few decades.
|
